X10 MSE Extraction System

Loading...

The X10 MSE (multi-solvent extractor), affectionately referred to as “The Judge”, is the company’s flagship extraction system. Utilizing hydrocarbon or ethanol solvents, the X10 processes more than 10 lbs of material per run with an average 55 minute recovery time* making it ideal for mid-level commercial production and craft applications. With patent pending jacketed vessels, the X10 comes equipped with on-demand heating and chilling, providing the system with maximum control and ease of operation.

  • Compatible for use with Butane, Propane, Pentane, and Ethanol
  • Rated for low temp conditions (-40C or below recommended)
  • 8-15 lbs per batch capacity (see yield matrix)
  • Patent pending vessel temperature control systems
  • German made, NRTL listed temperature control
  • Hydrocarbon and ethanol rated instrumentation valve systems (3/8″)
  • ASME certified high pressure vent downs
  • 3/8″ PTFE/SS feed hosing (UL-21 compliant)
  • ASME burst tested to over 2000PSI
  • ASME rated sight glasses on solvent and collection vessels Viton/PTFE gaskets
  • 40 lbs hydrocarbon solvent capacity/9 gallon ethanol capacity
  • Basket filtering
  • ln-line dewaxing
  • Vacuum jacket insulated solvent/dewax vessels
  • Nitrogen/Argon assist ready
  • Clamp-less mounting for easy loading/unloading
  • Pre-plumbed for chillers and heaters
  • Ultra-efficient internal temperature coil mechanisms
  • One year warranty on pumps, heaters, and chillers
  • Five year warranty on steel
  • Volatile, EPR reviewed, Closed Loop, Type 7 process for licensed operations (when used with hydrocarbon solvent)
  • Compatible with singular and mixed hydrocarbon solvents for superior extraction capability and product production
  • Approximate cycle time of 55-85 minutes when used with GC 5000 compressor
  • Certified for Class 1, Division 1 environments
  • 97%+ cannabinoid and terpene removal
  • Minimal solvent loss per batch (less than 4% per run)
  • Customized hydrocarbon extraction for high end product production, e.g., HTFSE, THC-a crystalline and “Sauce”
  • Non-Volatile, EPR reviewed, Closed Loop, Type 6 process for licensed operations (when used with ethanol solvent)
  • Pressurized Aqueous Cold Ethanol Extraction (PACEE) for superior full spectrum cannabinoid and terpene removal
  • 30L of ethanol used per run
  • Approximate 15L/h recovery rate with 50L UL listed rotovap
  • Approximate 2.25H processing time per run (single batch with full recovery)
  • 3H processing time (triple batch with full recovery)
  • Certified for Class 1, Division 2 environments
  • 95%+ cannabinoid and terpene removal
  • N2 pressurized saturation compatible up to 200PSI for excellent solubility (ASME certified vessels)
  • Up to 3 runs per solvent batch
  • Full spectrum yields great for high CBD hemp products
  • Chiller options to maximize cooling capacity
    • Huber CC-505
    • Huber CC-508
    • Huber CC-515
    • Huber Unistate 815
    • Julabo FP50-HE
    • Julabo FP52-SL
    • Julabo FP55-SL
    • Julabo FP89-HL
  • Heater
    • Julabo BC12 recirculating heat bath
  • ASME-U stamped vessels
  • ASME certified high pressure clamps (6″+) Build report
  • Serial number
  • EPR Reviewed
  • Third party engineer report
  • Pressure test report
  • ASME spec high pressure vent down system
  • UL-21 compliant hose system
  • DOT and trans-fill compliant
  • Volatile and non-volatile license complaint (dependent on solvent use, i.e., Type 6 and/or Type 7 license)
  • Compliant in all regulated jurisdictions

The Precision® Advantage

Ease of Use
Quality of Build
Speed of Extraction
Efficient Operation

X40 MSE Extraction System

The X40 MSE (multi-solvent extractor) is the company’s mid-size batch extraction system. Utilizing hydrocarbon or ethanol solvents, the X40 MSE processes up to 40lbs of material per run* making it ideal for mid or large level commercial production and craft applications. With patent pending jacketed vessels, the X40 MSE comes equipped with on-demand heating and chilling, providing the system with maximum control and ease of operation for a diverse range of product production.

  • Approximately 100L, 30-50lb material capacity* (see yield matrix)
  • Ultra user-friendly, ergonomic design
  • Drop-in stainless steel material baskets
  • Swagelok valve systems
  • UL-21 compliant hose systems
  • Rated for ethanol, butane and propane
  • Baffled jacketing on collection vessel
  • Vacuum jacketing on solvent vessel with internal cooling coil
  • Molecular sieve for moisture removal from Live Resin production
  • Excellent throughput for scaled hemp production
  • 100% ASME stamped and rated vessels
  • 4 material vessels for easy nonstop operation
  • SL-12 with HST booster heater
  • 100% compression fittings
  • Volatile, EPR reviewed, closed loop, Type 7 compliant process for licensed operations (when used with hydrocarbon solvent)
  • Compatible with singular and mixed hydrocarbon solvents for superior extraction capability and product production
  • Approximate 45 minutes processing time per run* (single material column)
  • Approximate 2 hours processing time per run (quad material columns)
  • Certified for Class 1, Division 1 enviroments
  • 97%+ cannabinoid and terpene removal
  • Minimal solvent loss per batch (less than 4% per run)
  • Customized mid scale hydrocarbon extraction for high yield product production, e.g., HTFSE, THC-a crystalline and “Sauce”
  • Full spectrum yields great for high CBD hemp products
  • Non-volatile, EPR reviewed, closed loop, Type 6 compliant process for licensed operations (when used with ethanol solvent)
  • Pressurized Aqueous Cold Ethanol Extraction (PACEE) for superior full spectrum cannabinoid and terpene removal
  • 100L of ethanol used per run
  • Approximate 1.5 hour processing time per run* (30-50lb single batch with recovery via a 18g/hr FFE)
  • 2 hour processing time* (triple batch with recovery)
  • 95%+ cannabinoid and terpene removal
  • N2 pressurized saturation compatible up to 200PSI
  • Up to 3 runs per solvent batch
  • Full spectrum yields great for high CBD hemp products
  • Huber CC-515
  • Huber Unistat 815
  • Huber Unistat 915
  • Julabo FP-55
  • Julabo FP-89
  • Julabo FP(W)-91SL
  • 100L dewax vessel with basket filtration
  • GC 5000 recovery pump
  • ASME-U stamped vessels
  • ASME certified high pressure clamps (6″+) Build report
  • Serial number
  • EPR Reviewed
  • Third party engineer report
  • Pressure test report
  • ASME spec high pressure vent down system
  • UL-21 compliant hose system
  • DOT and trans-fill compliant
  • Volatile and non-volatile license complaint (dependent on solvent use, i.e., Type 6 and/or Type 7 license)
  • Compliant in all regulated jurisdictions
Loading...

PXP v2017 Extraction System

The PXP, also known as “The Predator”, processes up to 15 lbs of material per run* while still maintaining the precise artisan control of a smaller system. This makes the PXP ideal for high level applications desiring to mix both craft concentrate and crude oil production. With patent pending jacketed vessels, the PXP system comes equipped with Julabo temperature control units providing the unit with maximum control and ease of operation.

  • 15 lbs material capacity
  • Up to 80 lbs of processing per day
  • Rated for n-Butane and 100% Propane or mix
  • Active or Passive (passive with butane only)
  • Patent pending vessel temperature control via custom heater and chiller
  • Rated for n-Butane and 100% Propane or mix
  • Vacuum jacketing on solvent tank and dewax column
  • Ergonomic 28″ x 36″ footprint for maximum floor space efficiency
  • Nickel stacked electropolished welds
  • Sight glasses on material column, collection tank, dewax and solvent tank
  • Inner condenser coils in solvent tank and dewax column
  • Julabo, German engineered, UL listed temperature controls
  • Inline dewaxing
  • Viton gaskets
  • High pressure clamps
  • Jacketed hot water bath collection vessel and expansion column
  • Compound pressure gauges
  • RA-52 or better, 3A compliant internal polishing
  • Comes standard with Julabo:
    • SL-12 Heat Bath Recirculator
    • FP89-HL Chiller
  • Stackable and variable filtering
  • 35 lbs solvent holding capacity
  • Nitrogen assist ready
  • Full mounting rack with wheels
  • Shipped fully assembled/pressure tested
  • American Society of Mechanical Engineers, 3A, National Fire Protection
  • Association 58 LPG compliant
  • Engineer Peer Reviewed:
    • California
    • Colorado
    • Illinois
    • Maryland
    • Nevada
    • Oregon
    • Pennsylvania
    • Washington
  • 3A Sanitary food grade compliant
  • Class 1, Division 1 compliant

The Precision® Advantage

Ease of Use
Quality of Build
Speed of Extraction
Efficient Operation
Loading...

PX40 Extraction System

Loading...

The PX40, also known as “The Executioner”, is the world’s largest extraction system. The PX40 processes up to 90 lbs of material per run with a 4 hour recovery time*, making it ideal for large volume commercial production. Like the X10, the PX40 comes equipped with on-demand heating and chilling, providing the system with maximum control and ease of operation.

  • Up to 90 lbs of material processing per run
  • Up to 360 lbs material processing per 10 hour shift
  • Rated for n-Butane and 100% Propane or mix
  • 180L material capacity (80+ lbs) (approx.)
  • Temperature controlled solvent vessel via FPW91-SL Chiller
  • Dual SL-12 recirculating heat bath
  • GC 5000 recovery pump
  • LPG rated valve systems (3/8”)
  • ASME certified high pressure vent downs
  • 3/8” PTFE/SS feed hosing (UL-21 compliant)
  • 5/8” PTFE/SS recovery hosing (UL-21 compliant)
  • 355L solvent tank size
  • 415L collection vessel size
  • Viton/PTFE gaskets
  • 1” certified sight glasses tested to 1,000 PSI
  • 8”/12” man hole vessel cleanouts
  • Nitrogen/argon assist ready
  • Rack mounted, easy load/unload material columns
  • Pre-plumbed for chillers and heaters
  • Heavy duty legs and lockable wheels
  • Dixon/Bradford valve assemblies (¾”, 1”)
  • Full one year warranty on pumps, heaters, and chillers
  • Full five year warranty on steel
  • Built to ASME standards
  • “EPR” Engineer Peer Reviewed
  • ASME-U stamped vessels
  • ASME certified high pressure clamps (6”+)
  • Build report
  • Serial number
  • Third party engineer report
  • Pressure test report
  • ASME/i502/CO/NV compliant warning systems
  • ASME spec high pressure vent down system
  • UL-21 compliant hose system
  • Compliant in ALL regulated jurisidictions
  • American Society of Mechanical Engineers
  • National Fire Protection Association
  • 3A
  • Association 58 LPG compliant
  • Engineer Peer Reviewed:
    • California
    • Colorado
    • Illinois
    • Maryland
    • Nevada
    • Oregon
    • Pennsylvania
    • Washington
  • 3A Sanitary food grade compliant
  • Class 1, Division 1 compliant

The Precision® Advantage

Ease of Use
Quality of Build
Speed of Extraction
Efficient Operation

*Actual amount of material per run and recovery times on any PX extraction system varies depending on composition, cut and moisture of input material, humidity and environmental factors, processing temperatures and operator experience.

Contact Us Now

Precision® has the equipment and know-how you need to succeed!

Professional extraction equipment, training and support... Made with Precision®
Contact Us Now